Jump to content
MaLd0n

Hackintosh Guide - High Sierra / Mojave / Catalina on X299 with Clover Bootloader

Recommended Posts

use this folder

CLOVER.zip

is still freezing and does not come the file MaLd0n SERIE 10,20,30.txt or what file should I put in System DSDT? :(

Share this post


Link to post
Share on other sites
freeze where?
when I'm moving or copying folders it freezes and I have to turn it off to be able to move it back

Share this post


Link to post
Share on other sites

use a fresh install, install clover and replace with my clover folder above

Share this post


Link to post
Share on other sites

use a fresh install, install clover and replace with my clover folder above

It's a bit faster but it keeps getting stuck when I open a clover or when I'm coping or dragging files


Added in 16 minutes 47 seconds:

another problem, when the shutdown or restart does not start, it stays the apple and the bar but does not load

Share this post


Link to post
Share on other sites

Can you patch this motherboard's dsdt file?


my motherboard is ASUS TUF X299 Mark2


BIOS Version is 1401.


attached file is my motherboard's dsdt file.


extracted by clover bootloader.

DSDT_ASUS_TUF_X299_MARK2_1401.zip

(45.97 KiB) Downloaded 1 time

 

Hello mate, your motherboard is pretty much the same as mine, I have the x299 TUF 1, all that was need was:


change EC0 to EC

4543305f

45435f5f


Check page 4 too check what was needed for mine.

Share this post


Link to post
Share on other sites

Hello mate, your motherboard is pretty much the same as mine, I have the x299 TUF 1, all that was need was:


change EC0 to EC

4543305f

45435f5f


Check page 4 too check what was needed for mine.

 

thank you for telling me. I will apply it and write the results again.

Share this post


Link to post
Share on other sites

Can you patch this motherboard's dsdt file?


my motherboard is ASUS TUF X299 Mark2


BIOS Version is 1401.


attached file is my motherboard's dsdt file.

DSDT.aml.zip

for a full patch u need post a full files

RunMe.app


Added in 2 minutes 18 seconds:

Hello mate, your motherboard is pretty much the same as mine, I have the x299 TUF 1, all that was need was:


change EC0 to EC

4543305f

45435f5f

 

if u rename a device need inject a correct usb properties, all mobos need a many many patches for work good, in x299 need a 200 or 300 changes per patch ;) essentials, cosmetics, etc

Share this post


Link to post
Share on other sites

I will report.

The DSDT for TUF X299 Mark2 produced by madl0n was not able to boot.

mark2_1.thumb.jpeg.e5ca682022382767187d10b0d0caec7e.jpeg

Stop on this screen.

mark2_2.thumb.jpeg.b559210d15e8bf3afb1010a9447f7795.jpeg

And this breaks the screen.


However, DSDT for TUF X299 Mark1 was able to boot and install Mac OS X high sierra.

But I can not use Thunderbolt.

If Thunderbolt is enabled in the BIOS, booting will stop.

 

mark1_thunderon.thumb.jpeg.d86f57b11e83cbd340ba8fa56cdcdac1.jpeg

 

I've learned how to fix this. I tried to fix it by adding npci = 0x2000 or npci = 0x3000 to the boot option,

 

mark1_thunderon_npci.thumb.jpeg.dea96e814164fdd158b150f2bc206c6d.jpeg

 

After a little more work, this screen is no longer in progress.

 

Send me yoiui-iMac-Pro.zip

 

I will attach the 'send_me' data for this system.

Share this post


Link to post
Share on other sites

remove dsdt, enable thunderbolt, boot into system and extract new SEND_ME

Share this post


Link to post
Share on other sites

Post by MaLd0n » 30 Aug 2018, 08:46


remove dsdt, enable thunderbolt, boot into system and extract new SEND_ME

 

If I delete DSDT.aml of X299 Mark1, this screen will pop up and I can not boot.

 

nodsdt_x299_mark2.thumb.jpeg.cc73bdb744be038d9a691fdcaa446fc6.jpeg

 

I can not boot this screen up,

And I can not boot with the boot option -f -x.

After searching, I installed FakePCIID + XHCIMux but I could not boot it.

USB2.0 has keyboard and boot usb, but the result is the same.

I can not run send_me because it is not bootable.

Share this post


Link to post
Share on other sites

by MaLd0n » 30 Aug 2018, 15:34


use other usb port

 

I tried all the other USB ports.

Copy the EFI / Clover folder to an empty 30GB SSD and connect to SATA

I have loaded the boot loader, but it is the same symptom.

When booting with USB,

When booting to SATA,

Finally, after Still Waiting for root device

Kernel panic (screen shot) occurs.

 

ec_1.thumb.jpg.4e92033188db1e83758e0e931b77af67.jpg

ec_2.thumb.jpg.a7073bb02b56bf67458a8ba8c63f128d.jpg

ec_3.thumb.jpg.4d5771751e344b0619ccfaa0d1b06e61.jpg

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...