guidelamuta Posted July 10, 2019 Share Posted July 10, 2019 SABERTOOTH P67 + RX 280 WON'T BOOT TO INSTALLER I tried all bios and EFI configurations that I found, always get the Forbidden Symbol. Any ideias? [Tried Mojave and High Sierra] Thx Quote Link to comment Share on other sites More sharing options...
Administrators MaLd0n Posted July 10, 2019 Administrators Share Posted July 10, 2019 [ref]guidelamuta[/ref], ahci enable? Quote Support Olarila Vanilla Hackintosh by making a donation HERE About Premium Users you can check HERE Problems with Paypal HERE Link to comment Share on other sites More sharing options...
guidelamuta Posted July 10, 2019 Author Share Posted July 10, 2019 Yes MaLd0n, SATA Mode Selection - AHCI S.M.A.R.T Status Check - Enabled Quote Link to comment Share on other sites More sharing options...
Administrators MaLd0n Posted July 10, 2019 Administrators Share Posted July 10, 2019 [ref]guidelamuta[/ref], use usb 2 port Quote Support Olarila Vanilla Hackintosh by making a donation HERE About Premium Users you can check HERE Problems with Paypal HERE Link to comment Share on other sites More sharing options...
guidelamuta Posted July 10, 2019 Author Share Posted July 10, 2019 I will try tonight. Thank you very much. Quote Link to comment Share on other sites More sharing options...
guidelamuta Posted July 10, 2019 Author Share Posted July 10, 2019 Hi again MaLd0n, I tried the USB 2.0 ports and got black screen instead the forbidden one. Then I did disable all this options (everythink was Enable, except Marvel): https://i.imgur.com/c1pC62I.jpg' alt='IMGUR>'> I don't know what options worked out, but I manage to boot the Mojave image. But then I got this message: https://i.imgur.com/rolbTb4.jpg' alt='IMGUR>'> There is any way to bypass this? Sorry for all the trouble. Added in 13 minutes 20 seconds: I changed to iMac 18,2 and WORKED! Muito obrigado pela ajuda! Quote Link to comment Share on other sites More sharing options...
Administrators MaLd0n Posted July 11, 2019 Administrators Share Posted July 11, 2019 [ref]guidelamuta[/ref], use smbios iMac13,2, work too Quote Support Olarila Vanilla Hackintosh by making a donation HERE About Premium Users you can check HERE Problems with Paypal HERE Link to comment Share on other sites More sharing options...
guidelamuta Posted July 12, 2019 Author Share Posted July 12, 2019 Hi MaLd0n, me again. I manage to install everything, smbios 13,2, but... When I installed clover via UEFI, Clover won't show up. When I installed clover via Legacy, Clover boots, but when all the steps finish and should get to the system I get a black screen. When boot with the Olarila Mojave Pen Drive, the system works fine. Any tips? Quote Link to comment Share on other sites More sharing options...
Administrators MaLd0n Posted July 13, 2019 Administrators Share Posted July 13, 2019 [ref]guidelamuta[/ref], copy efi folder fom Olarila usb stick to ur hdd/ssd Quote Support Olarila Vanilla Hackintosh by making a donation HERE About Premium Users you can check HERE Problems with Paypal HERE Link to comment Share on other sites More sharing options...
guidelamuta Posted July 13, 2019 Author Share Posted July 13, 2019 Didn't work, but in reverse, I used your EFI folder for sandybridge in the PENDRIVE clover folder, and the system is perfect. I don't know what is causing this, but one possible solution is leave a slave pendrive forever booting the system. Quote Link to comment Share on other sites More sharing options...
