HELP! INTEL HD GRAPHICS 4400 DON'T WORK ON MY HIGH SIERRA BUT READ AS 3MB.

[premiere001]

Helloo there,

I have Installed Olarila High sierra on my Dell Optilex 3020. SPECS;

Intel Hd 4400 Graphics

RAM; 16GB

Core i3

500GB HDD

Everything else is working Fine Except my graphics. I am a film editor/Journalist and I really need to Change my Resolution to 1920x1080. I have Tried so many things ie using Switchrezx, Clover configurator(which I have very little knowledge about) etc. I am unable to make my Intel hd 4400 Graphics read right. It reads Intel HD 4400 3mb.

 

Any help will be highly appreciated. If someone can configure for me my config.plist file, I will be very Thankful. I am Booting Using config.plist2 from Olarila High sierra.

Edited May 2, 2020 by premiere001

[MaLd0n]

https://www.olarila.com/topic/6420-guide-mobile-intel-hd-graphics/

[premiere001]

Many thanks for the Incredible fast  Reply. This Site is So awesome. Am gonna try this Out and See if it's Gonna Work. I am on desktop not Laptop.

I am relatively new to Olarila and I have a Question; In my EFI Folder, there are two Config.plist files. One is named " Config.plist" and the Other is named  "Config.plist2". I can only boot Using Config.plist2.

In this case therefore, Do I replace the Config.plist in my efi with the on in the link U posted above for Intel HD 4400 and then Delete Config.plist2? Please give me a Procedure.  Thank u in advance.

Edited May 2, 2020 by premiere001

[MaLd0n]

u try with InjectIntel only?

[premiere001]

Yes. I have tried with inject intel Only. The Result is that Everything Loads fines(the many codes that Run). But Immediately when it's time for the Apple Logo to Load (and then the Enter Password Wizard Comes Up), I Only Get a BlackScreen.

[MaLd0n]

try with previous version virtualsmc and whatevergreen

[premiere001]

thank U 4 the reply. What do u exactly Mean by"try with previous version virtualsmc and whatevergreen". Do U mean i should I should delete lilu and whatever green from kext>other or just try with and then Put virtualsmc and whatevergreen previous versions in kext>other?

[MaLd0n]

yes, dont use last version

many people report many problems

[premiere001]

I have Used WhateverGreen1.1.7.RELEASE and VirtualSMC-1.1.0-RELEASE but I experience the same thing as i described above.

What I did;

1. I dragged the whateverGreen and Virtual SMC Kext to EFI/KEXT/OTHER.

2. I Replaced the config.plist from the one in the HD4600, 4400 and 4200 zip file.

3. I then open this config.plist file with clover configurator and then check inject Intel.

4. I then Restart my Hackintosh.

But Immediately when it's time for the Apple Logo to Load (and then the Enter Password Wizard Comes Up), I Only Get a BlackScreen.

[premiere001]

here is the Config plist i use. can U please do anything u can do to it to Help. I haven't modified it in any way. Thank u.

HD4600, 4400 and 4200.zip

[Arturo Miranda]

On 5/3/2020 at 5:13 AM, premiere001 said:

here is the Config plist i use. can U please do anything u can do to it to Help. I haven't modified it in any way. Thank u.

HD4600, 4400 and 4200.zip 2.73 kB · 10 downloads

thanks!!! friend!!!

 

works perfect H4400 in Catalina