Sierra 10.12.6 stop booting and not even the installer USD flashdrive works

[icecold]

For years Sierra worked like a cinch, after installing it from a Vanilla Olarila 10.12.6 USB stick ... but today, it started refusing to boot all the sudden ...

AppleKeyStore Errors make it went into kernel panic, but the problem is now worst, because even the USB Sierra installer is rebooting when I try to run it from Clover!!!

I've used an old Yosemite stick in another hard drive and installed Yosemite, and it's working fine, but Sierra, for some reason REFUSES to boot ...

I've tried everything, disabling hard drives, just booting without anything but the USB stick ... always the same problem

and now even using just the USB stick to boot into Sierra, fails!!! with a reboot!!!

My configuration, is an ASROCK H61M-VG3, the motherboard doesn't have any video, so I am using an ATI Radeon 6870HD, and 8Gb DD3 RAM ... recognized as 1600 by Apple but the UEFI recognizes it as 1333...

2.59 GHz Intel Core i5(Dual core CELERON)

working fine until yesterday, the only kext, I installed was VOODOOHDA ... that's it ... but it worked fine with it for a week ... so it's weird it can be the culprit ...

[MaLd0n]

[ref]icecold[/ref], use native audio

https://Olarila.com/forum/viewtopic.php?f=28&t=9788

[icecold]

Thanks [ref]MaLd0n[/ref], !!! That and to successfully deselect the IGPU Monitor in the UEFI settings did the trick!!! Apparently that mode makes the system load the INTEL kexts and then it goes into PANIC!!! BTW I am configuring audio, Hope the injected patches work on ALC662 ...

[/img]

[icecold]

I have the ALC662, and I followed all the instructions, the only problem is I got a bunch of errors after compiling with the injected patch, is that normal?

[MaLd0n]

[ref]icecold[/ref], post one full dump here with runme.app

[icecold]

ok here's the dump>>>

Send me ic3Xs-iMac.zip

[MaLd0n]

[ref]icecold[/ref], use this efi with my dsdt

https://Olarila.com/files/Clover.Folder/CLOVER.SERIES.CHIPSET.zip

DSDT.aml.zip

[icecold]

Hi [ref]MaLd0n[/ref],

Thank you for your files ... BTW I added your DSDT.aml to EFI/CLOVER/ACPI/patched, and I opened the BOOT Options and is pointing to DSDT.aml ...

Am I doing something wrong, where can I check logs to see if it's actually loading it? It seems not to ...

I checked CLOVER logs and it seems to load the DSDT.aml

1:632 0:000 - [00]: (change EHC1 to EH01) lenToFind: 4, lenToReplace: 4

1:632 0:000 - [01]: (change EHC2 to EH02) lenToFind: 4, lenToReplace: 4

1:632 0:000 - [02]: (change EUSB to EH01) lenToFind: 4, lenToReplace: 4

1:632 0:000 - [03]: (change USBE to EH02) lenToFind: 4, lenToReplace: 4

1:632 0:000 - [04]: (change AZAL to HDEF) lenToFind: 4, lenToReplace: 4

1:632 0:000 - [05]: (change HDAS to HDEF) lenToFind: 4, lenToReplace: 4

1:632 0:000 - [06]: (change XHCI to XHC) lenToFind: 4, lenToReplace: 4

1:632 0:000 - [07]: (change XHC1 to XHC) lenToFind: 4, lenToReplace: 4

1:632 0:000 - [08]: (change HECI to IMEI) lenToFind: 4, lenToReplace: 4

The thing is nothing is recognized as a sound device in Sound Settings ... the list is empty ...

[MaLd0n]

[ref]icecold[/ref], Extract new send_me

--Run_Me

RunMe.app

[icecold]

Done

Here it goes

Send me ic3Xs-iMac.zip

[MaLd0n]

[ref]icecold[/ref], just put in clover/acpi/patched and set DSDT.aml in acpi tab dsdt name

[icecold]

As you can see from my screenshot the DSDT is there

https://imgur.com/RJ0Rn7G' alt='IMGUR>'>

Also in Clover configurator is showing up

https://imgur.com/WwzwPgD' alt='IMGUR>'>

[MaLd0n]

[ref]icecold[/ref],

[icecold]

Exactly what I did and didn't work ...

1. It's on the boot screen, under ACPI Patching(DSDT.aml)

2. The file path is EFI/CLOVER/ACPI/patched

3. In Clover Configurator under ACPI it shows the name ... DSDT.aml

No devices are recognized ...

[MaLd0n]

[ref]icecold[/ref], extract new send_me with my file

[icecold]

Send me file

Send me ic3Xs-iMac.zip

[MaLd0n]

[ref]icecold[/ref], post ur efi folder too

[icecold]

My EFI folder is the one you sent ...

CLOVER.SERIES.CHIPSET.zip

[icecold]

I just tried with all layouts that are related to the ALC662, and I mounted EFI and copied both CLOVER and BOOT there, so now my mounted EFI has all the kexts, including AppleALC 1.4.1 and Lilo 1.3.8.

Besides the DSDT.aml

and

I tested all layouts in Clover Configurator, and NOT a single one worked!!!

As my AUDIO hardware is recognized by Hackintool under PCI as Intel 6 Series/C200, I was wondering if that could be a reason why it's not working ...

DCPI Manager also recognizes it as an Intel 6 Series/C200 device 1C20 and under status it doesn't see it ... it just displays 2 network interfaces, the Realtek 8165E/8111E-VL and my Huawei LTE modem(I use to connect to my ISP). The Graphics Card also isn't there ... it's display under the PCI List, but not under the Status TAB. The PCI list also shows the HDMI audio device, on the Radeon 6870HD card, also not detected.

[MaLd0n]

[ref]icecold[/ref], EFI.zip

 

REMOVE DISABLE, I THINK IS AppleHDADisabler.kext

[icecold]

I noticed my hackintosh is booting from your Olarila sierra version usb, as it's the only way it doesn't give an error, therefore, what I did was to open Clover Configurator, mount the EFI on the USB and tried with all the layouts available for the ALC662, however none worked, then I also added your DSDT.aml to the EFI partition on the USB drive, and that also didn't work, I checked logs with bdmesg and it seems to load the DSDT the changes and correctly configure the layout ids I saved, in each attempt.

THe HDMI is there, the AUDIO layout id is also saved and loaded

=== [ FixBiosDsdt ] =======================================

7:787 0:000 VideoCard devID=0x67381002

7:787 0:000 DisplayADR1[0] = 0x10000, DisplayADR2[0] = 0x0

7:787 0:000 USBADR[0] = 0x1A0000 and PCIe = 0xFFFE

7:923 0:136 Audio HDA (addr:0x1B0000) setting specified layout-id=7 (0x7)

7:923 0:000 USBADR[1] = 0x1D0000 and PCIe = 0xFFFE

7:923 0:000 Patching DSDT:

No sound devices are recognized though ...

Added in 23 minutes 37 seconds:

I Removed AppleHDADisabler.kext from S/L/E and moved it to Backup Extensions just in case but the sound still doesn't work .. the weird thing is VoodooHDA made it work ...

I also placed the AppleHDA.kext under EFI/Clover/kexts/Other, on the USB drive EFI ... and still no sound ...

The weird thing is under VoodooHDA it worked fine, except it misconfigured by itself ... all the time ...

[icecold]

It's only recognizing my Logitech USB headset ... but not the Spica stereo out 3.5mm plug ... Green rear ...

Added in 35 minutes 17 seconds:

This is from a Controllers.plist is it possible to insert it into Clover's config.plist?

Device

41712

Name

200 Series PCH HD Audio

Patches

Count

6

Find

cKEAAA==

MinKernel

16

Name

AppleHDAController

Replace

8KIAAA==

Count

1

Find

hoBwoQ==

MinKernel

16

Name

AppleHDAController

Replace

hoDwog==

Vendor

Intel

[MaLd0n]

[ref]icecold[/ref], u just need inject layout-id

[icecold]

[ref]MaLd0n[/ref],

I did that with all layout-ids I've found in Resources for the ALC662 ...

5,7,11,12,13,15,16,17

None worked ... some worked for a while only with my USB Headset ... the others did nothing, I made sure AppleALC was on the EFI and loading before AppleHDA ...

=== [ FixBiosDsdt ] =======================================

9:088 0:000 VideoCard devID=0x67381002

9:088 0:000 DisplayADR1[0] = 0x10000, DisplayADR2[0] = 0x0

9:088 0:000 USBADR[0] = 0x1A0000 and PCIe = 0xFFFE

9:225 0:136 Audio HDA (addr:0x1B0000) setting specified layout-id=11 (0xB)

9:225 0:000 USBADR[1] = 0x1D0000 and PCIe = 0xFFFE

9:225 0:000 Patching DSDT:

9:225 0:000 - [change EHC1 to EH01]: pattern 45484331, bin not found / already patched!

9:225 0:000 - [change EHC2 to EH02]: pattern 45484332, bin not found / already patched!

9:225 0:000 - [change EUSB to EH01]: pattern 45555342, bin not found / already patched!

9:225 0:000 - [change USBE to EH02]: pattern 55534245, bin not found / already patched!

9:225 0:000 - [change AZAL to HDEF]: pattern 415A414C, bin not found / already patched!

9:225 0:000 - [change HDAS to HDEF]: pattern 48444153, bin not found / already patched!

9:226 0:000 - [change XHCI to XHC]: pattern 58484349, bin not found / already patched!

9:226 0:000 - [change XHC1 to XHC]: pattern 58484331, bin not found / already patched!

9:226 0:000 - [change HECI to IMEI]: pattern 48454349, bin not found / already patched!

[MaLd0n]

[ref]icecold[/ref], somee mobos(long time) have a ghost codec in some bios version