Ok so with the attached config.plist config.plist.zip (this is your file with additional acpi fix) and Olarila EFI folder, it boot and here are the runme files : http://s000.tinyupload.com/?file_id=44330319618464641445 The attached photo show how it hangs during the boot with your config.plist files without the additional patch :IMG_5704.JPG.zip One other thing : I had to launch the runme app twice as the first time, it tooks the wrong EFI files : on my EFI partition, I have 2 folders : "EFI" in which there are the Oralila files used for booting, and a second folder "EFI4920" with my files (I rename it to keep it there during the tests with your EFI folder). Apparently, runme app is dumping the files from EFI4920 and not from EFI folder. I had to remove my folder in order for runme app to dump the right files.
As I had a USB key that was working, I checked the differences and added few ACPI fixes to your config.plist which is now booting. I also move to FakeSMC.kext as the VirtualSMC.kext seems to not work : the VirtualSmc.efi driver is missing in your EFI files. New reports here : http://s000.tinyupload.com/?file_id=56054489708317283416
Hi Trying to get Mojave / Catalina on my old Hack. With Mojave, it boots but sleep does not work (it hangs after wake up) and when I restart, it has changed my BIOS settings, I have to reload Default and change the following again : AHCI, HPET64 and no full logo. I am currently using Clover 4920 for Mojave and plan to use v5100 for Catalina I have Gigabyte GA-H67MA-UD2H-B3 bios F8, SandyBridge i3-2105, GT710. To get the GT710 working, I use SMBIOS 14.2 (or also 13.2) Catalina might need the EC patch in the DSDT. Would be great to get DSDT/SSDT patched files (and maybe config.plist as well) to get it working RunMe link : http://s000.tinyupload.com/?file_id=01015283800325773373
Hi Tried to get the file from RunMe but it does not work. I have a Gigabyte H67MA-UD2H-B3 with an SandyBridge i3-2105 SandyBridge so I took the EFI folder files from the site for CHIPSET SERIES 5, 6, 7, 8, 9 (NEHALEM / SANDY BRIDGE / IVY BRIDGE / HASWELL / BROADWELL) and when I reboot, it hangs at line [PCI configuration begin] With my EFI folder, HighSierra is properly booting with Clover 4920 in Legacy mode. Why your EFI folder do not work ? Should I upgrade to Clover v2.5 ?
Hi I am updating my old hack (from Mavericks), used as an HTPC connected to my TV, to HighSierra 10.13.6 (17G65) and Mojave 10.14.6 (18G95) with an MSI GT710 1Gb and this works fine with HS but I got a black screen with Mojave. My MB is a Gigabyte H67MA-UD2H-B3 with a i3-2105 (Sandy Bridge) with HD3000 and a single hard disk with HS and Mojave installed in 2 partitions, booting Clover 4920, SMBIOS 14.1, display is a Dell P2217H with DisplayPort and HDMI. I first installed HS and Mojave using the HD3000 and both are running well using the Display Port cable (I used patched HD3000 driver from HS for Mojave). Then I disable the IGP in the bios, installed the MSI GT710 and moved to HDMI cable (there is no DP on the MSI) : * HS recognized the card and boot properly. It recognize the card as Model GK208B, Device ID 0x128B10DE * Mojave starts and run (as the disk light flash some time) but no display : black screen to grey then no signal then black The only change I made for the GT710 was to remove Inject Intel from config.plist So what's wrong ? I though GT710 was OOB in Mojave ? I do not know if Mojave load the right driver and/or if it fails to use the right port. I found some posts saying there might have some problems with GT710/Mojave and made some tests : I tried to put lilu 1.3.8 and whatevergreen 1.3.3 in EFI/clover/kext/others, I tried to change system from 14.1 to 14.2 and 18.1 but not change Any idea ? How can I check what Mojave is loading as graphics driver and therefore find where is the problem ? Why HS works really OOB and not Mojave ? I have attached the config.plist I used for HS and the one for Mojave, main difference is the Model to 13.1 for Mojave, and the clover boot.log with a first boot with Mojave then HS. I have a second issue which is overscan on my TV. Whith HD3000, I was able to fix that by changing the value of the key "pscn" from 10000 to 9834 in the file /var/db/.com.apple.iokit.graphics But when I connect my TV to the HDMI port of the GT710, I have instead of pscn a key named "oscn" with a value of 0 and dot not know how to change. I tried to remove oscn and put the same pscn value but on the next boot, oscn appear again and the screen still overscan. Any help on the 2 issues with be appreciated. config.plist.zip